Total
46 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2023-22405 | 1 Juniper | 15 Ex4600, Ex4600-vc, Ex4650 and 12 more | 2023-02-03 | N/A | 6.5 MEDIUM |
| An Improper Preservation of Consistency Between Independent Representations of Shared State vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause a Denial of Service (DoS) to device due to out of resources. When a device is configured with "service-provider/SP style" switching, and mac-limiting is configured on an Aggregated Ethernet (ae) interface, and then a PFE is restarted or the device is rebooted, mac-limiting doesn't work anymore. Please note that the issue might not be apparent as traffic will continue to flow through the device although the mac table and respective logs will indicate that mac limit is reached. Functionality can be restored by removing and re-adding the MAC limit configuration. This issue affects Juniper Networks Junos OS on QFX5k Series, EX46xx Series: All versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3 on; 21.4 versions prior to 21.4R3 on; 22.1 versions prior to 22.1R2 on. | |||||
| CVE-2021-31361 | 1 Juniper | 44 Junos, Ptx1000, Ptx1000-72q and 41 more | 2022-10-27 | 5.0 MEDIUM | 5.3 MEDIUM |
| An Improper Check for Unusual or Exceptional Conditions vulnerability combined with Improper Handling of Exceptional Conditions in Juniper Networks Junos OS on QFX Series and PTX Series allows an unauthenticated network based attacker to cause increased FPC CPU utilization by sending specific IP packets which are being VXLAN encapsulated leading to a partial Denial of Service (DoS). Continued receipted of these specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX Series: All versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS on PTX Series: All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2. | |||||
| CVE-2022-22226 | 1 Juniper | 35 Ex4300, Ex4300-24p, Ex4300-24p-s and 32 more | 2022-10-21 | N/A | 6.5 MEDIUM |
| In VxLAN scenarios on EX4300-MP, EX4600, QFX5000 Series devices an Uncontrolled Memory Allocation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated adjacently located attacker sending specific packets to cause a Denial of Service (DoS) condition by crashing one or more PFE's when they are received and processed by the device. Upon automatic restart of the PFE, continued processing of these packets will cause the memory leak to reappear. Depending on the volume of packets received the attacker may be able to create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP, EX4600, QFX5000 Series: 17.1 version 17.1R1 and later versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S7, 19.2R3-S1; 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Junos OS versions prior to 17.1R1. | |||||
| CVE-2020-1679 | 1 Juniper | 20 Junos, Ptx1000, Ptx10001-36mr and 17 more | 2022-08-05 | 4.3 MEDIUM | 7.5 HIGH |
| On Juniper Networks PTX and QFX Series devices with packet sampling configured using tunnel-observation mpls-over-udp, sampling of a malformed packet can cause the Kernel Routing Table (KRT) queue to become stuck. KRT is the module within the Routing Process Daemon (RPD) that synchronized the routing tables with the forwarding tables in the kernel. This table is then synchronized to the Packet Forwarding Engine (PFE) via the KRT queue. Thus, when KRT queue become stuck, it can lead to unexpected packet forwarding issues. An administrator can monitor the following command to check if there is the KRT queue is stuck: user@device > show krt state ... Number of async queue entries: 65007 <--- this value keep on increasing. When this issue occurs, the following message might appear in the /var/log/messages: DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Too many delayed route/nexthop unrefs. Op 2 err 55, rtsm_id 5:-1, msg type 2 DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Memory usage of M_RTNEXTHOP type = (0) Max size possible for M_RTNEXTHOP type = (7297134592) Current delayed unref = (60000), Current unique delayed unref = (18420), Max delayed unref on this platform = (40000) Current delayed weight unref = (60000) Max delayed weight unref on this platform= (400000) curproc = rpd This issue affects Juniper Networks Junos OS on PTX/QFX Series: 17.2X75 versions prior to 17.2X75-D105; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D420, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1. | |||||
| CVE-2021-0217 | 1 Juniper | 21 Ex2300, Ex2300-c, Ex2300m and 18 more | 2022-08-05 | 3.3 LOW | 7.4 HIGH |
| A vulnerability in processing of certain DHCP packets from adjacent clients on EX Series and QFX Series switches running Juniper Networks Junos OS with DHCP local/relay server configured may lead to exhaustion of DMA memory causing a Denial of Service (DoS). Over time, exploitation of this vulnerability may cause traffic to stop being forwarded, or to crashing of the fxpc process. When Packet DMA heap utilization reaches 99%, the system will become unstable. Packet DMA heap utilization can be monitored through the following command: user@junos# request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 213301a8 536870488 387228840 149641648 27 Kernel 1 91800000 8388608 3735120 4653488 55 DMA 2 92000000 75497472 74452192 1045280 1 PKT DMA DESC 3 d330000 335544320 257091400 78452920 23 Bcm_sdk 4 96800000 184549376 2408 184546968 99 Packet DMA <--- 5 903fffe0 20971504 20971504 0 0 Blob An indication of the issue occurring may be observed through the following log messages: Dec 10 08:07:00.124 2020 hostname fpc0 brcm_pkt_buf_alloc:523 (buf alloc) failed allocating packet buffer Dec 10 08:07:00.126 2020 hostname fpc0 (buf alloc) failed allocating packet buffer Dec 10 08:07:00.128 2020 hostname fpc0 brcm_pkt_buf_alloc:523 (buf alloc) failed allocating packet buffer Dec 10 08:07:00.130 2020 hostnameC fpc0 (buf alloc) failed allocating packet buffer This issue affects Juniper Networks Junos OS on EX Series and QFX Series: 17.4R3 versions prior to 17.4R3-S3; 18.1R3 versions between 18.1R3-S6 and 18.1R3-S11; 18.2R3 versions prior to 18.2R3-S6; 18.3R3 versions prior to 18.3R3-S4; 18.4R2 versions prior to 18.4R2-S5; 18.4R3 versions prior to 18.4R3-S6; 19.1 versions between 19.1R2 and 19.1R3-S3; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S2, 20.2R2. Junos OS versions prior to 17.4R3 are unaffected by this vulnerability. | |||||
| CVE-2022-22210 | 1 Juniper | 30 Junos, Mx10, Mx10000 and 27 more | 2022-07-29 | N/A | 6.5 MEDIUM |
| A NULL Pointer Dereference vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX5000 Series and MX Series allows an unauthenticated adjacent attacker to cause a Denial of Service (DoS). On QFX5K Series and MX Series, when the PFE receives a specific VxLAN packet the Layer 2 Address Learning Manager (L2ALM) process will crash leading to an FPC reboot. Continued receipt of this specific packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX5000 Series, MX Series: 20.3 versions prior to 20.3R3-S3; 20.4 versions prior to 20.4R3-S2; 21.2 versions prior to 21.2R2-S1. This issue does not affect Juniper Networks Junos OS: All versions prior to 20.3R1; 21.1 version 21.1R1 and later versions. | |||||
| CVE-2022-22203 | 1 Juniper | 11 Ex4600, Ex4650, Junos and 8 more | 2022-07-27 | N/A | 6.5 MEDIUM |
| An Incorrect Comparison vulnerability in PFE of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a Denial of Service (DoS). On QFX5000 Series, and EX4600 and EX4650 platforms, the fxpc process will crash followed by the FPC reboot upon receipt of a specific hostbound packet. Continued receipt of these specific packets will create a sustained Denial of Service (DoS) condition. This issue only affects Juniper Networks Junos OS 19.4 version 19.4R3-S4. | |||||
| CVE-2021-31371 | 1 Juniper | 6 Junos, Qfx5100, Qfx5110 and 3 more | 2022-05-13 | 5.0 MEDIUM | 5.3 MEDIUM |
| Juniper Networks Junos OS uses the 128.0.0.0/2 subnet for internal communications between the RE and PFEs. It was discovered that packets utilizing these IP addresses may egress an QFX5000 Series switch, leaking configuration information such as heartbeats, kernel versions, etc. out to the Internet, leading to an information exposure vulnerability. This issue affects Juniper Networks Junos OS on QFX5110, QFX5120, QFX5200, QFX5210 Series, and QFX5100 with QFX 5e Series image installed: All versions prior to 17.3R3-S12; 18.1 versions prior to 18.1R3-S13; 18.3 versions prior to 18.3R3-S5; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2; | |||||
| CVE-2018-0049 | 1 Juniper | 58 Ex2200, Ex2200-vc, Ex2300 and 55 more | 2022-05-12 | 7.1 HIGH | 7.5 HIGH |
| A NULL Pointer Dereference vulnerability in Juniper Networks Junos OS allows an attacker to cause the Junos OS kernel to crash. Continued receipt of this specifically crafted malicious MPLS packet will cause a sustained Denial of Service condition. This issue require it to be received on an interface configured to receive this type of traffic. Affected releases are Juniper Networks Junos OS: 12.1X46 versions above and including 12.1X46-D76 prior to 12.1X46-D81 on SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 12.3R12-S10; 12.3X48 versions above and including 12.3X48-D66 prior to 12.3X48-D75 on SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 14.1X53-D47 on EX2200/VC, EX3200, EX3300/VC, EX4200, EX4300, EX4550/VC, EX4600, EX6200, EX8200/VC (XRE), QFX3500, QFX3600, QFX5100; 14.1X53 versions above and including 14.1X53-D115 prior to 14.1X53-D130 on QFabric System; 15.1 versions above and including 15.1F6-S10; 15.1R4-S9; 15.1R6-S6; 15.1 versions above and including 15.1R7 prior to 15.1R7-S2; 15.1X49 versions above and including 15.1X49-D131 prior to 15.1X49-D150 on SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 15.1X53 versions above 15.1X53-D233 prior to 15.1X53-D235 on QFX5200/QFX5110; 15.1X53 versions up to and including 15.1X53-D471 prior to 15.1X53-D590 on NFX150, NFX250; 15.1X53-D67 on QFX10000 Series; 15.1X53-D59 on EX2300/EX3400; 16.1 versions above and including 16.1R3-S8; 16.1 versions above and including 16.1R4-S9 prior to 16.1R4-S12; 16.1 versions above and including 16.1R5-S4; 16.1 versions above and including 16.1R6-S3 prior to 16.1R6-S6; 16.1 versions above and including 16.1R7 prior to 16.1R7-S2; 16.2 versions above and including 16.2R1-S6; 16.2 versions above and including 16.2R2-S5 prior to 16.2R2-S7; 17.1R1-S7; 17.1 versions above and including 17.1R2-S7 prior to 17.1R2-S9; 17.2R1-S6; 17.2 versions above and including 17.2R2-S4 prior to 17.2R2-S6; 17.2X75 versions above and including 17.2X75-D100 prior to X17.2X75-D101, 17.2X75-D110; 17.3 versions above and including 17.3R1-S4 on All non-SRX Series and SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 17.3 versions above and including 17.3R2-S2 prior to 17.3R2-S4 on All non-SRX Series and SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 17.3R3 on All non-SRX Series and SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 17.4 versions above and including 17.4R1-S3 prior to 17.4R1-S5 on All non-SRX Series and SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 17.4R2 on All non-SRX Series and SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 18.1 versions above and including 18.1R2 prior to 18.1R2-S3, 18.1R3 on All non-SRX Series and SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 18.2 versions above and including 18.2R1 prior to 18.2R1-S2, 18.2R1-S3, 18.2R2 on All non-SRX Series and SRX100, SRX110, SRX210, SRX220, SRX240m, SRX550m SRX650, SRX300, SRX320, SRX340, SRX345, SRX1500, SRX4100, SRX4200, SRX4600 and vSRX; 18.2X75 versions above and including 18.2X75-D5 prior to 18.2X75-D20. | |||||
| CVE-2021-0285 | 1 Juniper | 46 Ex4200, Ex4200-vc, Ex4300 and 43 more | 2022-04-26 | 5.0 MEDIUM | 7.5 HIGH |
| An uncontrolled resource consumption vulnerability in Juniper Networks Junos OS on QFX5000 Series and EX4600 Series switches allows an attacker sending large amounts of legitimate traffic destined to the device to cause Interchassis Control Protocol (ICCP) interruptions, leading to an unstable control connection between the Multi-Chassis Link Aggregation Group (MC-LAG) nodes which can in turn lead to traffic loss. Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. An indication that the system could be impacted by this issue is the following log message: "DDOS_PROTOCOL_VIOLATION_SET: Warning: Host-bound traffic for protocol/exception LOCALNH:aggregate exceeded its allowed bandwidth at fpc <fpc number> for <n> times, started at <timestamp>" This issue affects Juniper Networks Junos OS on QFX5000 Series and EX4600 Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R1-S1, 20.4R2. | |||||
| CVE-2022-22188 | 1 Juniper | 8 Ex4600, Ex4650, Junos and 5 more | 2022-04-21 | 4.3 MEDIUM | 7.5 HIGH |
| An Uncontrolled Memory Allocation vulnerability leading to a Heap-based Buffer Overflow in the packet forwarding engine (PFE) of Juniper Networks Junos OS allows a network-based unauthenticated attacker to flood the device with traffic leading to a Denial of Service (DoS). The device must be configured with storm control profiling limiting the number of unknown broadcast, multicast, or unicast traffic to be vulnerable to this issue. This issue affects: Juniper Networks Junos OS on QFX5100/QFX5110/QFX5120/QFX5200/QFX5210/EX4600/EX4650 Series; 20.2 version 20.2R1 and later versions prior to 20.2R2. This issue does not affect: Juniper Networks Junos OS versions prior to 20.2R1. | |||||
| CVE-2022-22174 | 1 Juniper | 12 Ex4600, Ex4600-vc, Ex4650 and 9 more | 2022-02-01 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in the processing of inbound IPv6 packets in Juniper Networks Junos OS on QFX5000 Series and EX4600 switches may cause the memory to not be freed, leading to a packet DMA memory leak, and eventual Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition. The following error logs may be observed using the "show heap" command and the device may eventually run out of memory if such packets are received continuously. Jan 12 12:00:00 device-name fpc0 (buf alloc) failed allocating packet buffer Jan 12 12:00:01 device-name fpc0 (buf alloc) failed allocating packet buffer user@device-name> request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 246fc1a8 536870488 353653752 183216736 34 Kernel 1 91800000 16777216 12069680 4707536 28 DMA 2 92800000 75497472 69997640 5499832 7 PKT DMA DESC 3 106fc000 335544320 221425960 114118360 34 Bcm_sdk 4 97000000 176160768 200 176160568 99 Packet DMA <<<<<<<<<<<<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects Juniper Networks Junos OS on QFX5000 Series, EX4600: 18.3R3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue does not affect Juniper Networks Junos OS: Any versions prior to 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2. | |||||
| CVE-2020-1689 | 1 Juniper | 6 Ex4300-mp, Junos, Qfx5100 and 3 more | 2022-01-01 | 3.3 LOW | 6.5 MEDIUM |
| On Juniper Networks EX4300-MP Series, EX4600 Series and QFX5K Series deployed in a Virtual Chassis configuration, receipt of a stream of specific layer 2 frames can cause high CPU load, which could lead to traffic interruption. This issue does not occur when the device is deployed in Stand Alone configuration. The offending layer 2 frame packets can originate only from within the broadcast domain where the device is connected. This issue affects Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series and QFX5K Series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2. | |||||
| CVE-2020-1618 | 1 Juniper | 16 Ex2300, Ex2300-c, Ex3400 and 13 more | 2021-11-22 | 6.9 MEDIUM | 6.8 MEDIUM |
| On Juniper Networks EX and QFX Series, an authentication bypass vulnerability may allow a user connected to the console port to login as root without any password. This issue might only occur in certain scenarios: • At the first reboot after performing device factory reset using the command “request system zeroize”; or • A temporary moment during the first reboot after the software upgrade when the device configured in Virtual Chassis mode. This issue affects Juniper Networks Junos OS on EX and QFX Series: 14.1X53 versions prior to 14.1X53-D53; 15.1 versions prior to 15.1R7-S4; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S4; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R2; 18.3 versions prior to 18.3R1-S7, 18.3R2. This issue does not affect Juniper Networks Junos OS 12.3. | |||||
| CVE-2020-1613 | 1 Juniper | 46 Ex2300, Ex2300-c, Ex3400 and 43 more | 2021-11-18 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in the BGP FlowSpec implementation may cause a Juniper Networks Junos OS device to terminate an established BGP session upon receiving a specific BGP FlowSpec advertisement. The BGP NOTIFICATION message that terminates an established BGP session is sent toward the peer device that originally sent the specific BGP FlowSpec advertisement. This specific BGP FlowSpec advertisement received from a BGP peer might get propagated from a Junos OS device running the fixed release to another device that is vulnerable causing BGP session termination downstream. This issue affects IPv4 and IPv6 BGP FlowSpec deployment. This issue affects Juniper Networks Junos OS: 12.3; 12.3X48 on SRX Series; 14.1X53 on EX and QFX Series; 15.1 versions prior to 15.1R7-S5; 15.1F versions prior to 15.1F6-S13; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D497 on NFX Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S12, 17.1R3; 17.2 versions prior to 17.2R2-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110, 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R1-S8, 17.4R2; 18.1 versions prior to 18.1R2-S4, 18.1R3; 18.2X75 versions prior to 18.2X75-D20. | |||||
| CVE-2020-1604 | 1 Juniper | 7 Ex4300, Ex4600, Junos and 4 more | 2021-11-18 | 5.0 MEDIUM | 5.3 MEDIUM |
| On EX4300, EX4600, QFX3500, and QFX5100 Series, a vulnerability in the IP firewall filter component may cause the firewall filter evaluation of certain packets to fail. This issue only affects firewall filter evaluation of certain packets destined to the device Routing Engine (RE). This issue does not affect the Layer 2 firewall filter evaluation nor does it affect the Layer 3 firewall filter evaluation destined to connected hosts. This issue may occur when evaluating both IPv4 or IPv6 packets. This issue affects Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D12 on QFX5100 Series and EX4600 Series; 14.1X53 versions prior to 14.1X53-D52 on QFX3500 Series; 14.1X53 versions prior to 14.1X53-D48 on EX4300 Series; 15.1 versions prior to 15.1R7-S3 on EX4300 Series; 16.1 versions prior to 16.1R7 on EX4300 Series; 17.1 versions prior to 17.1R3 on EX4300 Series; 17.2 versions prior to 17.2R3 on EX4300 Series; 17.3 versions prior to 17.3R2-S5, 17.3R3 on EX4300 Series; 17.4 versions prior to 17.4R2 on EX4300 Series; 18.1 versions prior to 18.1R3 on EX4300 Series; 18.2 versions prior to 18.2R2 on EX4300 Series. | |||||
| CVE-2019-0005 | 1 Juniper | 14 Ex2300, Ex2300-c, Ex3400 and 11 more | 2021-11-09 | 5.0 MEDIUM | 5.3 MEDIUM |
| On EX2300, EX3400, EX4600, QFX3K and QFX5K series, firewall filter configuration cannot perform packet matching on any IPv6 extension headers. This issue may allow IPv6 packets that should have been blocked to be forwarded. IPv4 packet filtering is unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS on EX and QFX series;: 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1R7; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 series; 15.1X53 versions prior to 15.1X53-D591 on EX2300/EX3400 series; 16.1 versions prior to 16.1R7; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R2. | |||||
| CVE-2019-0006 | 1 Juniper | 31 Ex2200, Ex2200-c, Ex2300 and 28 more | 2021-10-28 | 7.5 HIGH | 9.8 CRITICAL |
| A certain crafted HTTP packet can trigger an uninitialized function pointer deference vulnerability in the Packet Forwarding Engine manager (fxpc) on all EX, QFX and MX Series devices in a Virtual Chassis configuration. This issue can result in a crash of the fxpc daemon or may potentially lead to remote code execution. This issue only occurs when the crafted packet it destined to the device. Affected releases are Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D47 on EX and QFX Virtual Chassis Platforms; 15.1 versions prior to 15.1R7-S3 all Virtual Chassis Platforms 15.1X53 versions prior to 15.1X53-D50 on EX and QFX Virtual Chassis Platforms. | |||||
| CVE-2019-0043 | 1 Juniper | 47 Acx1000, Acx1100, Acx2000 and 44 more | 2021-10-28 | 5.0 MEDIUM | 7.5 HIGH |
| In MPLS environments, receipt of a specific SNMP packet may cause the routing protocol daemon (RPD) process to crash and restart. By continuously sending a specially crafted SNMP packet, an attacker can repetitively crash the RPD process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS : 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D48 on EX/QFX series; 15.1 versions prior to 15.1R4-S9, 15.1R7-S2; 15.1F6 versions prior to 15.1F6-S11; 15.1X49 versions prior to 15.1X49-D141, 15.1X49-D144, 15.1X49-D150 on SRX Series; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 15.1X53 versions prior to 15.1X53-D590 on EX2300/EX3400 Series; 15.1X54 on ACX Series; 16.1 versions prior to 16.1R3-S10, 16.1R4-S11, 16.1R6-S5, 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S6; 17.1 versions prior to 17.1R2-S8, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R1-S1, 18.1R2-S1, 18.1R3; 18.2X75 versions prior to 18.2X75-D10. | |||||
| CVE-2021-31370 | 1 Juniper | 15 Ex4600, Ex4600-vc, Ex4650 and 12 more | 2021-10-25 | 3.3 LOW | 6.5 MEDIUM |
| An Incomplete List of Disallowed Inputs vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX5000 Series and EX4600 Series allows an adjacent unauthenticated attacker which sends a high rate of specific multicast traffic to cause control traffic received from the network to be dropped. This will impact control protocols (including but not limited to routing-protocols) and lead to a Denial of Service (DoS). Continued receipt of this specific multicast traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX5000 and EX4600 Series: All versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2. | |||||