Total
23 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2022-22234 | 1 Juniper | 11 Ex2300, Ex2300-24mp, Ex2300-24p and 8 more | 2022-10-21 | N/A | 5.5 MEDIUM |
| An Improper Preservation of Consistency Between Independent Representations of Shared State vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a locally authenticated attacker with low privileges to cause a Denial of Service (DoS). If the device is very busy for example while executing a series of show commands on the CLI one or more SFPs might not be detected anymore. The system then changes its state to "unplugged" which is leading to traffic impact and at least a partial DoS. Once the system is less busy the port states return to their actual value. Indicators of compromise are log messages about unplugged SFPs and corresponding syspld messages without any physical or environmental cause. These can be checked by issuing the following commands: user@device# show log messages | match unplugged %PFE-6: fpc0 sfp-0/1/2 SFP unplugged %PFE-6: fpc0 sfp-0/1/3 SFP unplugged The following log messages will also be seen when this issue happens: fpc0 Error tvp_drv_syspld_read: syspld read failed for address <address> fpc0 Error[-1]:tvp_optics_presence_get - Syspld read failed for port <pic/port> fpc0 optics pres failed(-1) for pic <pic> port <port> fpc0 tvp_drv_syspld_read: i2c access retry count 200 This issue affects Juniper Networks Junos OS on EX2300 Series, EX3400 Series: All versions prior to 18.4R3-S11; 19.1 versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R1-S9, 19.2R3-S5; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S4; 20.2 versions prior to 20.2R3-S4; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2. | |||||
| CVE-2021-0217 | 1 Juniper | 21 Ex2300, Ex2300-c, Ex2300m and 18 more | 2022-08-05 | 3.3 LOW | 7.4 HIGH |
| A vulnerability in processing of certain DHCP packets from adjacent clients on EX Series and QFX Series switches running Juniper Networks Junos OS with DHCP local/relay server configured may lead to exhaustion of DMA memory causing a Denial of Service (DoS). Over time, exploitation of this vulnerability may cause traffic to stop being forwarded, or to crashing of the fxpc process. When Packet DMA heap utilization reaches 99%, the system will become unstable. Packet DMA heap utilization can be monitored through the following command: user@junos# request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 213301a8 536870488 387228840 149641648 27 Kernel 1 91800000 8388608 3735120 4653488 55 DMA 2 92000000 75497472 74452192 1045280 1 PKT DMA DESC 3 d330000 335544320 257091400 78452920 23 Bcm_sdk 4 96800000 184549376 2408 184546968 99 Packet DMA <--- 5 903fffe0 20971504 20971504 0 0 Blob An indication of the issue occurring may be observed through the following log messages: Dec 10 08:07:00.124 2020 hostname fpc0 brcm_pkt_buf_alloc:523 (buf alloc) failed allocating packet buffer Dec 10 08:07:00.126 2020 hostname fpc0 (buf alloc) failed allocating packet buffer Dec 10 08:07:00.128 2020 hostname fpc0 brcm_pkt_buf_alloc:523 (buf alloc) failed allocating packet buffer Dec 10 08:07:00.130 2020 hostnameC fpc0 (buf alloc) failed allocating packet buffer This issue affects Juniper Networks Junos OS on EX Series and QFX Series: 17.4R3 versions prior to 17.4R3-S3; 18.1R3 versions between 18.1R3-S6 and 18.1R3-S11; 18.2R3 versions prior to 18.2R3-S6; 18.3R3 versions prior to 18.3R3-S4; 18.4R2 versions prior to 18.4R2-S5; 18.4R3 versions prior to 18.4R3-S6; 19.1 versions between 19.1R2 and 19.1R3-S3; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S2, 20.2R2. Junos OS versions prior to 17.4R3 are unaffected by this vulnerability. | |||||
| CVE-2022-22221 | 1 Juniper | 86 Ex2200, Ex2200-c, Ex2200-vc and 83 more | 2022-07-29 | N/A | 7.8 HIGH |
| An Improper Neutralization of Special Elements vulnerability in the download manager of Juniper Networks Junos OS on SRX Series and EX Series allows a locally authenticated attacker with low privileges to take full control over the device. One aspect of this vulnerability is that the attacker needs to be able to execute any of the "request ..." or "show system download ..." commands. This issue affects Juniper Networks Junos OS on SRX Series and EX Series: All versions prior to 19.2R1-S9, 19.2R3-S5; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S8; 20.1 versions prior to 20.1R3-S4; 20.2 versions prior to 20.2R3-S4; 20.3 versions prior to 20.3R3-S3; 20.4 versions prior to 20.4R3-S2, 20.4R3-S3; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R2-S2, 21.2R3; 21.3 versions prior to 21.3R2, 21.3R3; 21.4 versions prior to 21.4R1-S1, 21.4R2. | |||||
| CVE-2022-22180 | 1 Juniper | 11 Ex2300, Ex2300-24mp, Ex2300-24p and 8 more | 2022-02-01 | 5.0 MEDIUM | 7.5 HIGH |
| An Improper Check for Unusual or Exceptional Conditions vulnerability in the processing of specific IPv6 packets on certain EX Series devices may lead to exhaustion of DMA memory causing a Denial of Service (DoS). Over time, exploitation of this vulnerability may cause traffic to stop being forwarded, or a crash of the fxpc process. An indication of the issue occurring may be observed through the following log messages: Sep 13 17:14:59 hostname : %PFE-3: fpc0 (buf alloc) failed allocating packet buffer Sep 13 17:14:59 hostname : %PFE-7: fpc0 brcm_pkt_buf_alloc:393 (buf alloc) failed allocating packet buffer When Packet DMA heap utilization reaches 99%, the system will become unstable. Packet DMA heap utilization can be monitored using the command: user@junos# request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 213301a8 536870488 387228840 149641648 27 Kernel 1 91800000 8388608 3735120 4653488 55 DMA 2 92000000 75497472 74452192 1045280 1 PKT DMA DESC 3 d330000 335544320 257091400 78452920 23 Bcm_sdk 4 96800000 184549376 2408 184546968 99 Packet DMA <<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects: Juniper Networks Junos OS 18.4 versions prior to 18.4R2-S10, 18.4R3-S10 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.1 versions prior to 19.1R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.3 versions prior to 19.3R3-S5 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.4 versions prior to 19.4R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.1 versions prior to 20.1R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.2 versions prior to 20.2R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.3 versions prior to 20.3R3-S2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.4 versions prior to 20.4R3-S1 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.1 versions prior to 21.1R2-S2, 21.1R3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.2 versions prior to 21.2R1-S2, 21.2R2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.3 versions prior to 21.3R1-S1, 21.3R2 on EX2300 Series, EX2300-MP Series, EX3400 Series. | |||||
| CVE-2021-0211 | 1 Juniper | 87 Ex2200, Ex2200-c, Ex2200-vc and 84 more | 2022-01-18 | 6.4 MEDIUM | 10.0 CRITICAL |
| An improper check for unusual or exceptional conditions in Juniper Networks Junos OS and Junos OS Evolved Routing Protocol Daemon (RPD) service allows an attacker to send a valid BGP FlowSpec message thereby causing an unexpected change in the route advertisements within the BGP FlowSpec domain leading to disruptions in network traffic causing a Denial of Service (DoS) condition. Continued receipt of these update messages will cause a sustained Denial of Service condition. This issue affects Juniper Networks: Junos OS: All versions prior to 17.3R3-S10 with the exceptions of 15.1X49-D240 on SRX Series and 15.1R7-S8 on EX Series; 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R2-S12, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S3; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R1-S3, 19.4R2-S3, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S3 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2. Junos OS Evolved: All versions prior to 20.3R1-S1-EVO, 20.3R2-EVO. | |||||
| CVE-2021-0275 | 1 Juniper | 24 Ex2300, Ex2300-c, Ex3400 and 21 more | 2022-01-18 | 9.3 HIGH | 8.8 HIGH |
| A Cross-site Scripting (XSS) vulnerability in J-Web on Juniper Networks Junos OS allows an attacker to target another user's session thereby gaining access to the users session. The other user session must be active for the attack to succeed. Once successful, the attacker has the same privileges as the user. If the user has root privileges, the attacker may be able to gain full control of the device. This issue affects: Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15 on EX Series; 12.3X48 versions prior to 12.3X48-D95 on SRX Series; 15.1 versions prior to 15.1R7-S6 on EX Series; 15.1X49 versions prior to 15.1X49-D200 on SRX Series; 16.1 versions prior to 16.1R7-S7; 16.2 versions prior to 16.2R2-S11, 16.2R3; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3; 19.1 versions prior to 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S3, 19.2R2; 19.3 versions prior to 19.3R2. | |||||
| CVE-2020-1618 | 1 Juniper | 16 Ex2300, Ex2300-c, Ex3400 and 13 more | 2021-11-22 | 6.9 MEDIUM | 6.8 MEDIUM |
| On Juniper Networks EX and QFX Series, an authentication bypass vulnerability may allow a user connected to the console port to login as root without any password. This issue might only occur in certain scenarios: • At the first reboot after performing device factory reset using the command “request system zeroize”; or • A temporary moment during the first reboot after the software upgrade when the device configured in Virtual Chassis mode. This issue affects Juniper Networks Junos OS on EX and QFX Series: 14.1X53 versions prior to 14.1X53-D53; 15.1 versions prior to 15.1R7-S4; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S4; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R2; 18.3 versions prior to 18.3R1-S7, 18.3R2. This issue does not affect Juniper Networks Junos OS 12.3. | |||||
| CVE-2020-1613 | 1 Juniper | 46 Ex2300, Ex2300-c, Ex3400 and 43 more | 2021-11-18 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in the BGP FlowSpec implementation may cause a Juniper Networks Junos OS device to terminate an established BGP session upon receiving a specific BGP FlowSpec advertisement. The BGP NOTIFICATION message that terminates an established BGP session is sent toward the peer device that originally sent the specific BGP FlowSpec advertisement. This specific BGP FlowSpec advertisement received from a BGP peer might get propagated from a Junos OS device running the fixed release to another device that is vulnerable causing BGP session termination downstream. This issue affects IPv4 and IPv6 BGP FlowSpec deployment. This issue affects Juniper Networks Junos OS: 12.3; 12.3X48 on SRX Series; 14.1X53 on EX and QFX Series; 15.1 versions prior to 15.1R7-S5; 15.1F versions prior to 15.1F6-S13; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D497 on NFX Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S12, 17.1R3; 17.2 versions prior to 17.2R2-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110, 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R1-S8, 17.4R2; 18.1 versions prior to 18.1R2-S4, 18.1R3; 18.2X75 versions prior to 18.2X75-D20. | |||||
| CVE-2019-0005 | 1 Juniper | 14 Ex2300, Ex2300-c, Ex3400 and 11 more | 2021-11-09 | 5.0 MEDIUM | 5.3 MEDIUM |
| On EX2300, EX3400, EX4600, QFX3K and QFX5K series, firewall filter configuration cannot perform packet matching on any IPv6 extension headers. This issue may allow IPv6 packets that should have been blocked to be forwarded. IPv4 packet filtering is unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS on EX and QFX series;: 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1R7; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 series; 15.1X53 versions prior to 15.1X53-D591 on EX2300/EX3400 series; 16.1 versions prior to 16.1R7; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R2. | |||||
| CVE-2019-0006 | 1 Juniper | 31 Ex2200, Ex2200-c, Ex2300 and 28 more | 2021-10-28 | 7.5 HIGH | 9.8 CRITICAL |
| A certain crafted HTTP packet can trigger an uninitialized function pointer deference vulnerability in the Packet Forwarding Engine manager (fxpc) on all EX, QFX and MX Series devices in a Virtual Chassis configuration. This issue can result in a crash of the fxpc daemon or may potentially lead to remote code execution. This issue only occurs when the crafted packet it destined to the device. Affected releases are Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D47 on EX and QFX Virtual Chassis Platforms; 15.1 versions prior to 15.1R7-S3 all Virtual Chassis Platforms 15.1X53 versions prior to 15.1X53-D50 on EX and QFX Virtual Chassis Platforms. | |||||
| CVE-2019-0043 | 1 Juniper | 47 Acx1000, Acx1100, Acx2000 and 44 more | 2021-10-28 | 5.0 MEDIUM | 7.5 HIGH |
| In MPLS environments, receipt of a specific SNMP packet may cause the routing protocol daemon (RPD) process to crash and restart. By continuously sending a specially crafted SNMP packet, an attacker can repetitively crash the RPD process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS : 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D48 on EX/QFX series; 15.1 versions prior to 15.1R4-S9, 15.1R7-S2; 15.1F6 versions prior to 15.1F6-S11; 15.1X49 versions prior to 15.1X49-D141, 15.1X49-D144, 15.1X49-D150 on SRX Series; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 15.1X53 versions prior to 15.1X53-D590 on EX2300/EX3400 Series; 15.1X54 on ACX Series; 16.1 versions prior to 16.1R3-S10, 16.1R4-S11, 16.1R6-S5, 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S6; 17.1 versions prior to 17.1R2-S8, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R1-S1, 18.1R2-S1, 18.1R3; 18.2X75 versions prior to 18.2X75-D10. | |||||
| CVE-2021-31368 | 1 Juniper | 6 Acx710, Ex2300, Ex2300-c and 3 more | 2021-10-26 | 7.8 HIGH | 7.5 HIGH |
| An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks JUNOS OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that kernel and netisr process are shown to be using a lot of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 16 root -72 - 0K 304K WAIT 1 839:40 88.96% intr{swi1: netisr 0} 0 root 97 - 0K 160K RUN 1 732:43 87.99% kernel{bcm560xgmac0 que} This issue affects Juniper Networks JUNOS OS on EX2300 Series, EX3400 Series, and ACX710: All versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2. | |||||
| CVE-2021-0289 | 1 Juniper | 229 Acx1000, Acx1100, Acx2000 and 226 more | 2021-07-28 | 2.9 LOW | 5.3 MEDIUM |
| When user-defined ARP Policer is configured and applied on one or more Aggregated Ethernet (AE) interface units, a Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability between the Device Control Daemon (DCD) and firewall process (dfwd) daemons of Juniper Networks Junos OS allows an attacker to bypass the user-defined ARP Policer. In this particular case the User ARP policer is replaced with default ARP policer. To review the desired ARP Policers and actual state one can run the command "show interfaces <> extensive" and review the output. See further details below. An example output is: show interfaces extensive | match policer Policer: Input: __default_arp_policer__ <<< incorrect if user ARP Policer was applied on an AE interface and the default ARP Policer is displayed Policer: Input: jtac-arp-ae5.317-inet-arp <<< correct if user ARP Policer was applied on an AE interface For all platforms, except SRX Series: This issue affects Juniper Networks Junos OS: All versions 5.6R1 and all later versions prior to 18.4 versions prior to 18.4R2-S9, 18.4R3-S9 with the exception of 15.1 versions 15.1R7-S10 and later versions; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; This issue does not affect Juniper Networks Junos OS versions prior to 5.6R1. On SRX Series this issue affects Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.4 versions prior to 19.4R3-S4; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect 18.4 versions prior to 18.4R1 on SRX Series. This issue does not affect Junos OS Evolved. | |||||
| CVE-2018-0043 | 1 Juniper | 48 Ex2200, Ex2200-c, Ex2300 and 45 more | 2021-06-21 | 5.8 MEDIUM | 8.8 HIGH |
| Receipt of a specific MPLS packet may cause the routing protocol daemon (RPD) process to crash and restart or may lead to remote code execution. By continuously sending specific MPLS packets, an attacker can repeatedly crash the RPD process causing a sustained Denial of Service. This issue affects both IPv4 and IPv6. This issue can only be exploited from within the MPLS domain. End-users connected to the CE device cannot cause this crash. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on QFX/EX Series; 14.1X53 versions prior to 14.1X53-D130 on QFabric Series; 15.1F6 versions prior to 15.1F6-S10; 15.1 versions prior to 15.1R4-S9 15.1R7; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D471 15.1X53-D490 on NFX Series; 16.1 versions prior to 16.1R3-S8 16.1R4-S8 16.1R5-S4 16.1R6-S4 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R1-S6 16.2R3; 17.1 versions prior to 17.1R1-S7 17.1R2-S6 17.1R3; 17.2 versions prior to 17.2R1-S6 17.2R2-S3 17.2R3; 17.2X75 versions prior to 17.2X75-D100 17.2X75-D42 17.2X75-D91; 17.3 versions prior to 17.3R1-S4 17.3R2-S2 17.3R3; 17.4 versions prior to 17.4R1-S3 17.4R2 . No other Juniper Networks products or platforms are affected by this issue. | |||||
| CVE-2021-0261 | 1 Juniper | 23 Ex2300, Ex2300-c, Ex3400 and 20 more | 2021-05-04 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in the HTTP/HTTPS service used by J-Web, Web Authentication, Dynamic-VPN (DVPN), Firewall Authentication Pass-Through with Web-Redirect, and Captive Portal allows an unauthenticated attacker to cause an extended Denial of Service (DoS) for these services by sending a high number of specific requests. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S17 on EX Series; 12.3X48 versions prior to 12.3X48-D105 on SRX Series; 15.1 versions prior to 15.1R7-S8; 15.1X49 versions prior to 15.1X49-D230 on SRX Series; 16.1 versions prior to 16.1R7-S8; 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2; 20.2 versions prior to 20.2R1-S1, 20.2R2. | |||||
| CVE-2021-0244 | 1 Juniper | 23 Ex2300, Ex2300-c, Ex3400 and 20 more | 2021-04-27 | 4.3 MEDIUM | 7.4 HIGH |
| A signal handler race condition exists in the Layer 2 Address Learning Daemon (L2ALD) of Juniper Networks Junos OS due to the absence of a specific protection mechanism to avoid a race condition which may allow an attacker to bypass the storm-control feature on devices. This issue is a corner case and only occurs during specific actions taken by an administrator of a device under certain specifics actions which triggers the event. The event occurs less frequently on devices which are not configured with Virtual Chassis configurations, and more frequently on devices configured in Virtual Chassis configurations. This issue is not specific to any particular Junos OS platform. An Indicator of Compromise (IoC) may be seen by reviewing log files for the following error message seen by executing the following show statement: show log messages | grep storm Result to look for: /kernel: GENCFG: op 58 (Storm Control Blob) failed; err 1 (Unknown) This issue affects: Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D49 on EX Series; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D191, 15.1X49-D200 on SRX Series; 16.1 versions prior to 16.1R7-S7; 16.2 versions prior to 16.2R2-S11, 16.2R3; 17.1 versions prior to 17.1R2-S11, 17.1R3; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R2-S6, 18.2R3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2. | |||||
| CVE-2019-0062 | 1 Juniper | 46 Csrx, Ex2200, Ex2200-c and 43 more | 2021-02-05 | 6.8 MEDIUM | 8.8 HIGH |
| A session fixation vulnerability in J-Web on Junos OS may allow an attacker to use social engineering techniques to fix and hijack a J-Web administrators web session and potentially gain administrative access to the device. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15 on EX Series; 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 14.1X53 versions prior to 14.1X53-D51; 15.1 versions prior to 15.1F6-S13, 15.1R7-S5; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238; 16.1 versions prior to 16.1R4-S13, 16.1R7-S5; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.3 versions prior to 17.3R3-S5; 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S2, 19.1R2. | |||||
| CVE-2021-0203 | 1 Juniper | 17 Ex2300, Ex2300-c, Ex2300m and 14 more | 2021-01-21 | 4.3 MEDIUM | 8.6 HIGH |
| On Juniper Networks EX and QFX5K Series platforms configured with Redundant Trunk Group (RTG), Storm Control profile applied on the RTG interface might not take affect when it reaches the threshold condition. Storm Control enables the device to monitor traffic levels and to drop broadcast, multicast, and unknown unicast packets when a specified traffic level is exceeded, thus preventing packets from proliferating and degrading the LAN. Note: this issue does not affect EX2200, EX3300, EX4200, and EX9200 Series. This issue affects Juniper Networks Junos OS on EX Series and QFX5K Series: 15.1 versions prior to 15.1R7-S7; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S5, 18.4R3-S3; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. | |||||
| CVE-2020-1661 | 1 Juniper | 32 Ex2300, Ex2300-c, Ex3400 and 29 more | 2020-10-26 | 4.3 MEDIUM | 5.3 MEDIUM |
| On Juniper Networks Junos OS devices configured as a DHCP forwarder, the Juniper Networks Dynamic Host Configuration Protocol Daemon (jdhcp) process might crash when receiving a malformed DHCP packet. This issue only affects devices configured as DHCP forwarder with forward-only option, that forward specified DHCP client packets, without creating a new subscriber session. The jdhcpd daemon automatically restarts without intervention, but continuous receipt of the malformed DHCP packet will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue can be triggered only by DHCPv4, it cannot be triggered by DHCPv6. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S16; 12.3X48 versions prior to 12.3X48-D105 on SRX Series; 14.1X53 versions prior to 14.1X53-D60 on EX and QFX Series; 15.1 versions prior to 15.1R7-S7; 15.1X49 versions prior to 15.1X49-D221, 15.1X49-D230 on SRX Series; 15.1X53 versions prior to 15.1X53-D593 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S5. | |||||
| CVE-2019-0071 | 1 Juniper | 4 Ex2300, Ex2300-c, Ex3400 and 1 more | 2020-09-28 | 7.2 HIGH | 7.8 HIGH |
| Veriexec is a kernel-based file integrity subsystem in Junos OS that ensures only authorized binaries are able to be executed. Due to a flaw in specific versions of Junos OS, affecting specific EX Series platforms, the Veriexec subsystem will fail to initialize, in essence disabling file integrity checking. This may allow a locally authenticated user with shell access to install untrusted executable images, and elevate privileges to gain full control of the system. During the installation of an affected version of Junos OS are installed, the following messages will be logged to the console: Initializing Verified Exec: /sbin/veriexec: Undefined symbol "__aeabi_uidiv" /sbin/veriexec: Undefined symbol "__aeabi_uidiv" /sbin/veriexec: Undefined symbol "__aeabi_uidiv" veriexec: /.mount/packages/db/os-kernel-prd-arm-32-20190221.70c2600_builder_stable_11/boot/brcm-hr3.dtb: Authentication error veriexec: /.mount/packages/db/os-kernel-prd-arm-32-20190221.70c2600_builder_stable_11/boot/contents.izo: Authentication error ... This issue affects Juniper Networks Junos OS: 18.1R3-S4 on EX2300, EX2300-C and EX3400; 18.3R1-S3 on EX2300, EX2300-C and EX3400. | |||||