Total
50 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2021-0294 | 1 Juniper | 8 Ex4600, Ex4650, Junos and 5 more | 2021-07-28 | 5.0 MEDIUM | 5.3 MEDIUM |
| A vulnerability in Juniper Networks Junos OS, which only affects the release 18.4R2-S5, where a function is inconsistently implemented on Juniper Networks Junos QFX5000 Series and EX4600 Series, and if "storm-control enhanced" is configured, can lead to the enhanced storm control filter group not be installed. It will cause storm control not to work hence allowing an attacker to cause high CPU usage or packet loss issues by sending a large amount of broadcast or unknown unicast packets arriving the device. This issue affects Juniper Networks QFX5100, QFX5110, QFX5120, QFX5200, QFX5210, EX4600, and EX4650, and QFX5100 with QFX 5e Series image installed. QFX5130 and QFX5220 are not affected from this issue. This issue affects Juniper Networks Junos OS 18.4R2-S5 on QFX5000 Series and EX4600 Series. No other product or platform is affected by this vulnerability. | |||||
| CVE-2021-0289 | 1 Juniper | 229 Acx1000, Acx1100, Acx2000 and 226 more | 2021-07-28 | 2.9 LOW | 5.3 MEDIUM |
| When user-defined ARP Policer is configured and applied on one or more Aggregated Ethernet (AE) interface units, a Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability between the Device Control Daemon (DCD) and firewall process (dfwd) daemons of Juniper Networks Junos OS allows an attacker to bypass the user-defined ARP Policer. In this particular case the User ARP policer is replaced with default ARP policer. To review the desired ARP Policers and actual state one can run the command "show interfaces <> extensive" and review the output. See further details below. An example output is: show interfaces extensive | match policer Policer: Input: __default_arp_policer__ <<< incorrect if user ARP Policer was applied on an AE interface and the default ARP Policer is displayed Policer: Input: jtac-arp-ae5.317-inet-arp <<< correct if user ARP Policer was applied on an AE interface For all platforms, except SRX Series: This issue affects Juniper Networks Junos OS: All versions 5.6R1 and all later versions prior to 18.4 versions prior to 18.4R2-S9, 18.4R3-S9 with the exception of 15.1 versions 15.1R7-S10 and later versions; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; This issue does not affect Juniper Networks Junos OS versions prior to 5.6R1. On SRX Series this issue affects Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.4 versions prior to 19.4R3-S4; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect 18.4 versions prior to 18.4R1 on SRX Series. This issue does not affect Junos OS Evolved. | |||||
| CVE-2021-0237 | 1 Juniper | 11 Ex4300-mp, Ex4600, Ex4650 and 8 more | 2021-07-23 | 3.3 LOW | 6.5 MEDIUM |
| On Juniper Networks EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series deployed as a Virtual Chassis with a specific Layer 2 circuit configuration, Packet Forwarding Engine manager (FXPC) process may crash and restart upon receipt of specific layer 2 frames. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4, 17.4R3-S5; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2; | |||||
| CVE-2018-0034 | 1 Juniper | 56 Ex2200, Ex2200-c, Ex2200-vc and 53 more | 2021-06-21 | 4.3 MEDIUM | 5.9 MEDIUM |
| A Denial of Service vulnerability exists in the Juniper Networks Junos OS JDHCPD daemon which allows an attacker to core the JDHCPD daemon by sending a crafted IPv6 packet to the system. This issue is limited to systems which receives IPv6 DHCP packets on a system configured for DHCP processing using the JDHCPD daemon. This issue does not affect IPv4 DHCP packet processing. Affected releases are Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S10 on EX Series; 12.3X48 versions prior to 12.3X48-D70 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on EX2200/VC, EX3200, EX3300/VC, EX4200, EX4300, EX4550/VC, EX4600, EX6200, EX8200/VC (XRE), QFX3500, QFX3600, QFX5100; 14.1X53 versions prior to 14.1X53-D130 on QFabric; 15.1 versions prior to 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10000 Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5110, QFX5200; 15.1X53 versions prior to 15.1X53-D471 on NFX 150, NFX 250; 16.1 versions prior to 16.1R3-S9, 16.1R4-S8, 16.1R5-S4, 16.1R6-S3, 16.1R7; 16.2 versions prior to 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.3 versions prior to 17.3R1-S4, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2. | |||||
| CVE-2018-0043 | 1 Juniper | 48 Ex2200, Ex2200-c, Ex2300 and 45 more | 2021-06-21 | 5.8 MEDIUM | 8.8 HIGH |
| Receipt of a specific MPLS packet may cause the routing protocol daemon (RPD) process to crash and restart or may lead to remote code execution. By continuously sending specific MPLS packets, an attacker can repeatedly crash the RPD process causing a sustained Denial of Service. This issue affects both IPv4 and IPv6. This issue can only be exploited from within the MPLS domain. End-users connected to the CE device cannot cause this crash. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on QFX/EX Series; 14.1X53 versions prior to 14.1X53-D130 on QFabric Series; 15.1F6 versions prior to 15.1F6-S10; 15.1 versions prior to 15.1R4-S9 15.1R7; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D471 15.1X53-D490 on NFX Series; 16.1 versions prior to 16.1R3-S8 16.1R4-S8 16.1R5-S4 16.1R6-S4 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R1-S6 16.2R3; 17.1 versions prior to 17.1R1-S7 17.1R2-S6 17.1R3; 17.2 versions prior to 17.2R1-S6 17.2R2-S3 17.2R3; 17.2X75 versions prior to 17.2X75-D100 17.2X75-D42 17.2X75-D91; 17.3 versions prior to 17.3R1-S4 17.3R2-S2 17.3R3; 17.4 versions prior to 17.4R1-S3 17.4R2 . No other Juniper Networks products or platforms are affected by this issue. | |||||
| CVE-2018-0008 | 1 Juniper | 40 Ex2200, Ex2300, Ex3300 and 37 more | 2021-06-16 | 7.2 HIGH | 6.2 MEDIUM |
| An unauthenticated root login may allow upon reboot when a commit script is used. A commit script allows a device administrator to execute certain instructions during commit, which is configured under the [system scripts commit] stanza. Certain commit scripts that work without a problem during normal commit may cause unexpected behavior upon reboot which can leave the system in a state where root CLI login is allowed without a password due to the system reverting to a "safe mode" authentication state. Lastly, only logging in physically to the console port as root, with no password, will work. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D71 on SRX; 12.3X48 versions prior to 12.3X48-D55 on SRX; 14.1 versions prior to 14.1R9; 14.1X53 versions prior to 14.1X53-D40 on QFX, EX; 14.2 versions prior to 14.2R7-S9, 14.2R8; 15.1 versions prior to 15.1F5-S7, 15.1F6-S8, 15.1R5-S6, 15.1R6; 15.1X49 versions prior to 15.1X49-D110 on SRX; 15.1X53 versions prior to 15.1X53-D232 on QFX5200/5110; 15.1X53 versions prior to 15.1X53-D49, 15.1X53-D470 on NFX; 15.1X53 versions prior to 15.1X53-D65 on QFX10K; 16.1 versions prior to 16.1R2. No other Juniper Networks products or platforms are affected by this issue. | |||||
| CVE-2021-0259 | 1 Juniper | 9 Junos, Junos Os Evolved, Qfx5100 and 6 more | 2021-05-04 | 3.3 LOW | 7.4 HIGH |
| Due to a vulnerability in DDoS protection in Juniper Networks Junos OS and Junos OS Evolved on QFX5K Series switches in a VXLAN configuration, instability might be experienced in the underlay network as a consequence of exceeding the default ddos-protection aggregate threshold. If an attacker on a client device on the overlay network sends a high volume of specific, legitimate traffic in the overlay network, due to an improperly detected DDoS violation, the leaf might not process certain L2 traffic, sent by spines in the underlay network. Continued receipt and processing of the high volume traffic will sustain the Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX5K Series: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R2-S8, 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S2, 20.3R2. Juniper Networks Junos OS Evolved on QFX5220: All versions prior to 20.3R2-EVO. | |||||
| CVE-2021-0247 | 1 Juniper | 20 Junos, Ptx1000, Ptx10001-36mr and 17 more | 2021-04-30 | 6.8 MEDIUM | 5.5 MEDIUM |
| A Race Condition (Concurrent Execution using Shared Resource with Improper Synchronization) vulnerability in the firewall process (dfwd) of Juniper Networks Junos OS allows an attacker to bypass the firewall rule sets applied to the input loopback filter on any interfaces of a device. This issue is detectable by reviewing the PFE firewall rules, as well as the firewall counters and seeing if they are incrementing or not. For example: show firewall Filter: __default_bpdu_filter__ Filter: FILTER-INET-01 Counters: Name Bytes Packets output-match-inet 0 0 <<<<<< missing firewall packet count This issue affects: Juniper Networks Junos OS 14.1X53 versions prior to 14.1X53-D53 on QFX Series; 14.1 versions 14.1R1 and later versions prior to 15.1 versions prior to 15.1R7-S6 on QFX Series, PTX Series; 15.1X53 versions prior to 15.1X53-D593 on QFX Series; 16.1 versions prior to 16.1R7-S7 on QFX Series, PTX Series; 16.2 versions prior to 16.2R2-S11, 16.2R3 on QFX Series, PTX Series; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2 on QFX Series, PTX Series; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3 on QFX Series, PTX Series; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7 on QFX Series, PTX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3 on QFX Series, PTX Series; 18.1 versions prior to 18.1R3-S9 on QFX Series, PTX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on QFX Series, PTX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1 on QFX Series, PTX Series; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R2-S7, 18.4R3 on QFX Series, PTX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on QFX Series, PTX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on QFX Series, PTX Series. | |||||
| CVE-2021-0222 | 1 Juniper | 12 Ex2300, Ex3400, Ex4300 and 9 more | 2021-02-05 | 6.1 MEDIUM | 7.4 HIGH |
| A vulnerability in Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending certain crafted protocol packets from an adjacent device with invalid payloads to the device. These crafted packets, which should be discarded, are instead replicated and sent to the RE. Over time, a Denial of Service (DoS) occurs. Continued receipt of these crafted protocol packets will cause an extended Denial of Service (DoS) condition, which may cause wider traffic impact due to protocol flapping. An indication of compromise is to check "monitor interface traffic" on the ingress and egress port packet counts. For each ingress packet, two duplicate packets are seen on egress. This issue can be triggered by IPv4 and IPv6 packets. This issue affects all traffic through the device. This issue affects: Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D53 on EX4300, QFX3500, QFX5100, EX4600; 15.1 versions prior to 15.1R7-S6 on EX4300, QFX3500, QFX5100, EX4600; 16.1 versions prior to 16.1R7-S7 on EX4300, QFX5100, EX4600; 17.1 versions prior to 17.1R2-S11 on EX4300, QFX5100, EX4600; 17.1 versions prior to 117.1R3-S2 on EX4300; 17.2 versions prior to 17.2R1-S9 on EX4300; 17.2 versions prior to 17.2R3-S3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7 on EX4300, QFX5100, EX4600, QFX5110, QFX5200; 17.4 versions prior to 17.4R2-S9, 17.4R3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200; 18.1 versions prior to 18.1R3-S9 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, EX2300, EX3400; 18.2 versions prior to 18.2R2-S7 on EX4300; 18.2 versions prior to 18.2R3-S3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, EX2300, EX3400; 18.3 versions prior to 18.3R2-S3, on EX4300; 18.3 versions prior to 18.3R1-S7, 18.3R3-S1 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on EX4300, QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400; 19.2 versions prior to 19.2R1-S4, 19.2R2 on EX4300; 19.2 versions prior to 19.2R1-S3, 19.2R2 on QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400; 19.3 versions prior to 19.3R2-S1, 19.3R3 on EX4300; 19.3 versions prior to 19.3R1-S1, 19.3R2, 19.3R3 on QFX5100, EX4600, QFX5110, QFX5200, QFX5210, QFX5120, EX4650, EX2300, EX3400; | |||||
| CVE-2020-1606 | 1 Juniper | 24 Junos, Qfx5110, Qfx5200 and 21 more | 2021-02-05 | 6.5 MEDIUM | 8.1 HIGH |
| A path traversal vulnerability in the Juniper Networks Junos OS device may allow an authenticated J-web user to read files with 'world' readable permission and delete files with 'world' writeable permission. This issue does not affect system files that can be accessed only by root user. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S13; 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 14.1X53 versions prior to 14.1X53-D51; 15.1F6 versions prior to 15.1F6-S13; 15.1 versions prior to 15.1R7-S5; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110 Series; 16.1 versions prior to 16.1R4-S13, 16.1R7-S5; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S2; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2. | |||||
| CVE-2020-1685 | 1 Juniper | 8 Junos, Qfx5100, Qfx5110 and 5 more | 2021-02-05 | 5.0 MEDIUM | 5.8 MEDIUM |
| When configuring stateless firewall filters in Juniper Networks EX4600 and QFX 5000 Series devices using Virtual Extensible LAN protocol (VXLAN), the discard action will fail to discard traffic under certain conditions. Given a firewall filter configuration similar to: family ethernet-switching { filter L2-VLAN { term ALLOW { from { user-vlan-id 100; } then { accept; } } term NON-MATCH { then { discard; } } when there is only one term containing a 'user-vlan-id' match condition, and no other terms in the firewall filter except discard, the discard action for non-matching traffic will only discard traffic with the same VLAN ID specified under 'user-vlan-id'. Other traffic (e.g. VLAN ID 200) will not be discarded. This unexpected behavior can lead to unintended traffic passing through the interface where the firewall filter is applied. This issue only affects systems using VXLANs. This issue affects Juniper Networks Junos OS on QFX5K Series: 18.1 versions prior to 18.1R3-S7, except 18.1R3; 18.2 versions prior to 18.2R2-S7, 18.2R3-S1; 18.3 versions prior to 18.3R1-S5, 18.3R2-S4, 18.3R3; 18.4 versions prior to 18.4R1-S7, 18.4R2-S1, 18.4R3; 19.1 versions prior to 19.1R1-S5, 19.1R2; 19.2 versions prior to 19.2R1-S5, 19.2R2. | |||||
| CVE-2021-0207 | 1 Juniper | 14 Ex2300, Ex3400, Ex4300 and 11 more | 2021-02-05 | 5.0 MEDIUM | 7.5 HIGH |
| An improper interpretation conflict of certain data between certain software components within the Juniper Networks Junos OS devices does not allow certain traffic to pass through the device upon receipt from an ingress interface filtering certain specific types of traffic which is then being redirected to an egress interface on a different VLAN. This causes a Denial of Service (DoS) to those clients sending these particular types of traffic. Such traffic being sent by a client may appear genuine, but is non-standard in nature and should be considered as potentially malicious, and can be targeted to the device, or destined through it for the issue to occur. This issues affects IPv4 and IPv6 traffic. An indicator of compromise may be found by checking log files. You may find that traffic on the input interface has 100% of traffic flowing into the device, yet the egress interface shows 0 pps leaving the device. For example: [show interfaces "interface" statistics detail] Output between two interfaces would reveal something similar to: Ingress, first interface: -------------------- Interface Link Input packets (pps) Output packets (pps) et-0/0/0 Up 9999999999 (9999) 1 (0) -------------------- Egress, second interface: -------------------- Interface Link Input packets (pps) Output packets (pps) et-0/0/1 Up 0 (0) 9999999999 (0) -------------------- Dropped packets will not show up in DDoS monitoring/protection counters as issue is not caused by anti-DDoS protection mechanisms. This issue affects: Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S7 on NFX250, QFX5K Series, EX4600; 17.4 versions prior to 17.4R2-S11, 17.4R3-S3 on NFX250, QFX5K Series, EX4600; 18.1 versions prior to 18.1R3-S9 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4600; 18.2 versions prior to 18.2R3-S3 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600; 18.3 versions prior to 18.3R3-S1 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 19.2 versions prior to 19.2R1-S5, 19.2R2 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 19.3 versions prior to 19.3R2-S3, 19.3R3 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 19.4 versions prior to 19.4R1-S2, 19.4R2 on NFX250, NFX350, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series. This issue does not affect Junos OS releases prior to 17.2R2. | |||||
| CVE-2019-0069 | 1 Juniper | 12 Acx5000, Ex4600, Junos and 9 more | 2021-02-05 | 2.1 LOW | 5.5 MEDIUM |
| On EX4600, QFX5100 Series, NFX Series, QFX10K Series, QFX5110, QFX5200 Series, QFX5110, QFX5200, QFX10K Series, vSRX, SRX1500, SRX4000 Series, vSRX, SRX1500, SRX4000, QFX5110, QFX5200, QFX10K Series, when the user uses console management port to authenticate, the credentials used during device authentication are written to a log file in clear text. This issue does not affect users that are logging-in using telnet, SSH or J-web to the management IP. This issue affects ACX, NFX, SRX, EX and QFX platforms with the Linux Host OS architecture, it does not affect other SRX and EX platforms that do not use the Linux Host OS architecture. This issue affects Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D110 on vSRX, SRX1500, SRX4000 Series; 15.1X53 versions prior to 15.1X53-D234 on QFX5110, QFX5200 Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10K Series; 17.1 versions prior to 17.1R2-S8, 17.1R3, on QFX5110, QFX5200, QFX10K Series; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3 on QFX5110, QFX5200, QFX10K Series; 17.3 versions prior to 17.3R2 on vSRX, SRX1500, SRX4000, QFX5110, QFX5200, QFX10K Series; 14.1X53 versions prior to 14.1X53-D47 on ACX5000, EX4600, QFX5100 Series; 15.1 versions prior to 15.1R7 on ACX5000, EX4600, QFX5100 Series; 16.1R7 versions prior to 16.1R7 on ACX5000, EX4600, QFX5100 Series; 17.1 versions prior to 17.1R2-S10, 17.1R3 on ACX5000, EX4600, QFX5100 Series; 17.2 versions prior to 17.2R3 on ACX5000, EX4600, QFX5100 Series; 17.3 versions prior to 17.3R3 on ACX5000, EX4600, QFX5100 Series; 17.4 versions prior to 17.4R2 on ACX5000, EX4600, QFX5100 Series; 18.1 versions prior to 18.1R2 on ACX5000, EX4600, QFX5100 Series; 15.1X53 versions prior to 15.1X53-D496 on NFX Series, 17.2 versions prior to 17.2R3-S1 on NFX Series; 17.3 versions prior to 17.3R3-S4 on NFX Series; 17.4 versions prior to 17.4R2-S4, 17.4R3 on NFX Series, 18.1 versions prior to 18.1R3-S4 on NFX Series; 18.2 versions prior to 18.2R2-S3, 18.2R3 on NFX Series; 18.3 versions prior to 18.3R1-S3, 18.3R2 on NFX Series; 18.4 versions prior to 18.4R1-S1, 18.4R2 on NFX Series. | |||||
| CVE-2021-0203 | 1 Juniper | 17 Ex2300, Ex2300-c, Ex2300m and 14 more | 2021-01-21 | 4.3 MEDIUM | 8.6 HIGH |
| On Juniper Networks EX and QFX5K Series platforms configured with Redundant Trunk Group (RTG), Storm Control profile applied on the RTG interface might not take affect when it reaches the threshold condition. Storm Control enables the device to monitor traffic levels and to drop broadcast, multicast, and unknown unicast packets when a specified traffic level is exceeded, thus preventing packets from proliferating and degrading the LAN. Note: this issue does not affect EX2200, EX3300, EX4200, and EX9200 Series. This issue affects Juniper Networks Junos OS on EX Series and QFX5K Series: 15.1 versions prior to 15.1R7-S7; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S5, 18.4R3-S3; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. | |||||
| CVE-2020-1661 | 1 Juniper | 32 Ex2300, Ex2300-c, Ex3400 and 29 more | 2020-10-26 | 4.3 MEDIUM | 5.3 MEDIUM |
| On Juniper Networks Junos OS devices configured as a DHCP forwarder, the Juniper Networks Dynamic Host Configuration Protocol Daemon (jdhcp) process might crash when receiving a malformed DHCP packet. This issue only affects devices configured as DHCP forwarder with forward-only option, that forward specified DHCP client packets, without creating a new subscriber session. The jdhcpd daemon automatically restarts without intervention, but continuous receipt of the malformed DHCP packet will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue can be triggered only by DHCPv4, it cannot be triggered by DHCPv6. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S16; 12.3X48 versions prior to 12.3X48-D105 on SRX Series; 14.1X53 versions prior to 14.1X53-D60 on EX and QFX Series; 15.1 versions prior to 15.1R7-S7; 15.1X49 versions prior to 15.1X49-D221, 15.1X49-D230 on SRX Series; 15.1X53 versions prior to 15.1X53-D593 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S5. | |||||
| CVE-2019-0014 | 1 Juniper | 17 Junos, Ptx1000, Ptx10002 and 14 more | 2020-07-22 | 5.0 MEDIUM | 7.5 HIGH |
| On QFX and PTX Series, receipt of a malformed packet for J-Flow sampling might crash the FPC (Flexible PIC Concentrator) process which causes all interfaces to go down. By continuously sending the offending packet, an attacker can repeatedly crash the FPC process causing a sustained Denial of Service (DoS). This issue affects both IPv4 and IPv6 packet processing. Affected releases are Juniper Networks Junos OS on QFX and PTX Series: 17.4 versions prior to 17.4R2-S1, 17.4R3; 18.1 versions prior to 18.1R3-S1; 18.2 versions prior to 18.2R1-S3, 18.2R2; 17.2X75 versions prior to 17.2X75-D91, 17.2X75-D100. | |||||
| CVE-2020-1607 | 1 Juniper | 44 Ex2300, Ex2300-c, Ex3400 and 41 more | 2020-01-24 | 4.3 MEDIUM | 6.1 MEDIUM |
| Insufficient Cross-Site Scripting (XSS) protection in J-Web may potentially allow a remote attacker to inject web script or HTML, hijack the target user's J-Web session and perform administrative actions on the Junos device as the targeted user. This issue affects Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D86, 12.3X48-D90 on SRX Series; 14.1X53 versions prior to 14.1X53-D51 on EX and QFX Series; 15.1F6 versions prior to 15.1F6-S13; 15.1 versions prior to 15.1R7-S5; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400 Series; 16.1 versions prior to 16.1R4-S13, 16.1R7-S5; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S2; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R2-S6, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.3 versions prior to 18.3R1-S6, 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S2, 19.1R2. | |||||
| CVE-2018-0045 | 1 Juniper | 23 Ex2300, Ex3400, Junos and 20 more | 2019-10-09 | 5.8 MEDIUM | 8.8 HIGH |
| Receipt of a specific Draft-Rosen MVPN control packet may cause the routing protocol daemon (RPD) process to crash and restart or may lead to remote code execution. By continuously sending the same specific Draft-Rosen MVPN control packet, an attacker can repeatedly crash the RPD process causing a prolonged denial of service. This issue may occur when the Junos OS device is configured for Draft-Rosen multicast virtual private network (MVPN). The VPN is multicast-enabled and configured to use Protocol Independent Multicast (PIM) protocol within the VPN. This issue can only be exploited from the PE device within the MPLS domain which is capable of forwarding IP multicast traffic in core. End-users connected to the CE device cannot cause this crash. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D70 on SRX Series; 15.1 versions prior to 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1F6; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 16.1 versions prior to 16.1R4-S9, 16.1R5-S4, 16.1R6-S3, 16.1R7; 16.2 versions prior to 16.2R1-S6, 16.2R2-S6, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R2-S4, 17.2R3; 17.3 versions prior to 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.1 versions prior to 18.1R2. No other Juniper Networks products or platforms are affected by this issue. | |||||
| CVE-2018-0060 | 1 Juniper | 15 Ex2300, Ex3200, Ex3400 and 12 more | 2019-10-09 | 4.3 MEDIUM | 5.9 MEDIUM |
| An improper input validation weakness in the device control daemon process (dcd) of Juniper Networks Junos OS allows an attacker to cause a Denial of Service to the dcd process and interfaces and connected clients when the Junos device is requesting an IP address for itself. Junos devices are not vulnerable to this issue when not configured to use DHCP. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D40 on SRX Series; 12.3X48 versions prior to 12.3X48-D20 on SRX Series; 14.1X53 versions prior to 14.1X53-D40 on EX2200/VC, EX3200, EX3300/VC, EX4200, EX4300, EX4550/VC, EX4600, EX6200, EX8200/VC (XRE), QFX3500, QFX3600, QFX5100; 15.1X49 versions prior to 15.1X49-D20 on SRX Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10000 Series; 15.1X53 versions prior to 15.1X53-D235 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D495 on NFX150, NFX250; 15.1X53 versions prior to 15.1X53-D590 on EX2300/EX3400; 15.1 versions prior to 15.1R7-S2. | |||||
| CVE-2018-0029 | 1 Juniper | 6 Ex2300, Ex3400, Junos and 3 more | 2019-10-09 | 6.1 MEDIUM | 6.5 MEDIUM |
| While experiencing a broadcast storm, placing the fxp0 interface into promiscuous mode via the 'monitor traffic interface fxp0' can cause the system to crash and restart (vmcore). This issue only affects Junos OS 15.1 and later releases, and affects both single core and multi-core REs. Releases prior to Junos OS 15.1 are unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1F6-S11, 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D140; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400; 15.1X53 versions prior to 15.1X53-D67 on QFX10K; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX; 16.1 versions prior to 16.1R3-S8, 16.1R5-S4, 16.1R6-S1, 16.1R7; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.2X75 versions prior to 17.2X75-D90, 17.2X75-D110; 17.3 versions prior to 17.3R1-S4, 17.3R2; 17.4 versions prior to 17.4R1-S3, 17.4R2. | |||||