Total
3 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2021-0216 | 1 Juniper | 3 Acx5448, Acx710, Junos | 2022-07-12 | 3.3 LOW | 6.5 MEDIUM |
| A vulnerability in Juniper Networks Junos OS running on the ACX5448 and ACX710 platforms may cause BFD sessions to flap when a high rate of transit ARP packets are received. This, in turn, may impact routing protocols and network stability, leading to a Denial of Service (DoS) condition. When a high rate of transit ARP packets are exceptioned to the CPU and BFD flaps, the following log messages may be seen: bfdd[15864]: BFDD_STATE_UP_TO_DOWN: BFD Session 192.168.14.3 (IFL 232) state Up -> Down LD/RD(17/19) Up time:11:38:17 Local diag: CtlExpire Remote diag: None Reason: Detect Timer Expiry. bfdd[15864]: BFDD_TRAP_SHOP_STATE_DOWN: local discriminator: 17, new state: down, interface: irb.998, peer addr: 192.168.14.3 rpd[15839]: RPD_ISIS_ADJDOWN: IS-IS lost L2 adjacency to peer on irb.998, reason: BFD Session Down bfdd[15864]: BFDD_TRAP_SHOP_STATE_UP: local discriminator: 17, new state: up, interface: irb.998, peer addr: 192.168.14.3 This issue only affects the ACX5448 Series and ACX710 Series routers. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS: 18.2 versions prior to 18.2R3-S8 on ACX5448; 18.3 versions prior to 18.3R3-S5 on ACX5448; 18.4 versions prior to 18.4R1-S6, 18.4R3-S7 on ACX5448; 19.1 versions prior to 19.1R3-S5 on ACX5448; 19.2 versions prior to 19.2R2, 19.2R3 on ACX5448; 19.3 versions prior to 19.3R3 on ACX5448; 19.4 versions prior to 19.4R3 on ACX5448; 20.1 versions prior to 20.1R2 on ACX5448; 20.2 versions prior to 20.2R2 on ACX5448 and ACX710. | |||||
| CVE-2021-31368 | 1 Juniper | 6 Acx710, Ex2300, Ex2300-c and 3 more | 2021-10-26 | 7.8 HIGH | 7.5 HIGH |
| An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks JUNOS OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that kernel and netisr process are shown to be using a lot of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 16 root -72 - 0K 304K WAIT 1 839:40 88.96% intr{swi1: netisr 0} 0 root 97 - 0K 160K RUN 1 732:43 87.99% kernel{bcm560xgmac0 que} This issue affects Juniper Networks JUNOS OS on EX2300 Series, EX3400 Series, and ACX710: All versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2. | |||||
| CVE-2021-0289 | 1 Juniper | 229 Acx1000, Acx1100, Acx2000 and 226 more | 2021-07-28 | 2.9 LOW | 5.3 MEDIUM |
| When user-defined ARP Policer is configured and applied on one or more Aggregated Ethernet (AE) interface units, a Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability between the Device Control Daemon (DCD) and firewall process (dfwd) daemons of Juniper Networks Junos OS allows an attacker to bypass the user-defined ARP Policer. In this particular case the User ARP policer is replaced with default ARP policer. To review the desired ARP Policers and actual state one can run the command "show interfaces <> extensive" and review the output. See further details below. An example output is: show interfaces extensive | match policer Policer: Input: __default_arp_policer__ <<< incorrect if user ARP Policer was applied on an AE interface and the default ARP Policer is displayed Policer: Input: jtac-arp-ae5.317-inet-arp <<< correct if user ARP Policer was applied on an AE interface For all platforms, except SRX Series: This issue affects Juniper Networks Junos OS: All versions 5.6R1 and all later versions prior to 18.4 versions prior to 18.4R2-S9, 18.4R3-S9 with the exception of 15.1 versions 15.1R7-S10 and later versions; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; This issue does not affect Juniper Networks Junos OS versions prior to 5.6R1. On SRX Series this issue affects Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.4 versions prior to 19.4R3-S4; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect 18.4 versions prior to 18.4R1 on SRX Series. This issue does not affect Junos OS Evolved. | |||||