Total
12 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2021-31361 | 1 Juniper | 44 Junos, Ptx1000, Ptx1000-72q and 41 more | 2022-10-27 | 5.0 MEDIUM | 5.3 MEDIUM |
| An Improper Check for Unusual or Exceptional Conditions vulnerability combined with Improper Handling of Exceptional Conditions in Juniper Networks Junos OS on QFX Series and PTX Series allows an unauthenticated network based attacker to cause increased FPC CPU utilization by sending specific IP packets which are being VXLAN encapsulated leading to a partial Denial of Service (DoS). Continued receipted of these specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX Series: All versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS on PTX Series: All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2. | |||||
| CVE-2022-22211 | 1 Juniper | 18 Junos Os Evolved, Ptx1000, Ptx1000-72q and 15 more | 2022-10-21 | N/A | 7.5 HIGH |
| A limitless resource allocation vulnerability in FPC resources of Juniper Networks Junos OS Evolved on PTX Series allows an unprivileged attacker to cause Denial of Service (DoS). Continuously polling the SNMP jnxCosQstatTable causes the FPC to run out of GUID space, causing a Denial of Service to the FPC resources. When the FPC runs out of the GUID space, you will see the following syslog messages. The evo-aftmand-bt process is asserting. fpc1 evo-aftmand-bt[17556]: %USER-3: get_next_guid: Ran out of Guid Space start 1748051689472 end 1752346656767 fpc1 audit[17556]: %AUTH-5: ANOM_ABEND auid=4294967295 uid=0 gid=0 ses=4294967295 pid=17556 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=6 fpc1 kernel: %KERN-5: audit: type=1701 audit(1648567505.119:57): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=17556 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=6 fpc1 emfd-fpa[14438]: %USER-5: Alarm set: APP color=red, class=CHASSIS, reason=Application evo-aftmand-bt fail on node Fpc1 fpc1 emfd-fpa[14438]: %USER-3-EMF_FPA_ALARM_REP: RaiseAlarm: Alarm(Location: /Chassis[0]/Fpc[1] Module: sysman Object: evo-aftmand-bt:0 Error: 2) reported fpc1 sysepochman[12738]: %USER-5-SYSTEM_REBOOT_EVENT: Reboot [node] [ungraceful reboot] [evo-aftmand-bt exited] The FPC resources can be monitored using the following commands: user@router> start shell [vrf:none] user@router-re0:~$ cli -c "show platform application-info allocations app evo-aftmand-bt" | grep ^fpc | grep -v Route | grep -i -v Nexthop | awk '{total[$1] += $5} END { for (key in total) { print key " " total[key]/4294967296 }}' Once the FPCs become unreachable they must be manually restarted as they do not self-recover. This issue affects Juniper Networks Junos OS Evolved on PTX Series: All versions prior to 20.4R3-S4-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO version 21.2R1-EVO and later versions; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R2-EVO; 22.1-EVO versions prior to 22.1R2-EVO. | |||||
| CVE-2022-22192 | 1 Juniper | 4 Junos Os Evolved, Ptx10004, Ptx10008 and 1 more | 2022-10-21 | N/A | 7.5 HIGH |
| An Improper Validation of Syntactic Correctness of Input vulnerability in the kernel of Juniper Networks Junos OS Evolved on PTX series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an incoming TCP packet destined to the device is malformed there is a possibility of a kernel panic. Only TCP packets destined to the ports for BGP, LDP and MSDP can trigger this. This issue only affects PTX10004, PTX10008, PTX10016. No other PTX Series devices or other platforms are affected. This issue affects Juniper Networks Junos OS Evolved: 20.4-EVO versions prior to 20.4R3-S4-EVO; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 20.4R1-EVO. | |||||
| CVE-2020-1679 | 1 Juniper | 20 Junos, Ptx1000, Ptx10001-36mr and 17 more | 2022-08-05 | 4.3 MEDIUM | 7.5 HIGH |
| On Juniper Networks PTX and QFX Series devices with packet sampling configured using tunnel-observation mpls-over-udp, sampling of a malformed packet can cause the Kernel Routing Table (KRT) queue to become stuck. KRT is the module within the Routing Process Daemon (RPD) that synchronized the routing tables with the forwarding tables in the kernel. This table is then synchronized to the Packet Forwarding Engine (PFE) via the KRT queue. Thus, when KRT queue become stuck, it can lead to unexpected packet forwarding issues. An administrator can monitor the following command to check if there is the KRT queue is stuck: user@device > show krt state ... Number of async queue entries: 65007 <--- this value keep on increasing. When this issue occurs, the following message might appear in the /var/log/messages: DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Too many delayed route/nexthop unrefs. Op 2 err 55, rtsm_id 5:-1, msg type 2 DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Memory usage of M_RTNEXTHOP type = (0) Max size possible for M_RTNEXTHOP type = (7297134592) Current delayed unref = (60000), Current unique delayed unref = (18420), Max delayed unref on this platform = (40000) Current delayed weight unref = (60000) Max delayed weight unref on this platform= (400000) curproc = rpd This issue affects Juniper Networks Junos OS on PTX/QFX Series: 17.2X75 versions prior to 17.2X75-D105; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D420, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1. | |||||
| CVE-2022-22216 | 1 Juniper | 12 Junos, Ptx1000, Ptx10001 and 9 more | 2022-07-29 | N/A | 4.3 MEDIUM |
| An Exposure of Sensitive Information to an Unauthorized Actor vulnerability in the PFE of Juniper Networks Junos OS on PTX Series and QFX10k Series allows an adjacent unauthenticated attacker to gain access to sensitive information. PTX1000 and PTX10000 Series, and QFX10000 Series and PTX5000 Series devices sometimes do not reliably pad Ethernet packets, and thus some packets can contain fragments of system memory or data from previous packets. This issue is also known as 'Etherleak' and often detected as CVE-2003-0001. This issue affects: Juniper Networks Junos OS on PTX1000 and PTX10000 Series: All versions prior to 18.4R3-S11; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. Juniper Networks Junos OS on QFX10000 Series and PTX5000 Series: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S6, 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R2. | |||||
| CVE-2022-22194 | 1 Juniper | 4 Junos Os Evolved, Ptx10003, Ptx10004 and 1 more | 2022-04-21 | 5.0 MEDIUM | 7.5 HIGH |
| An Improper Check for Unusual or Exceptional Conditions vulnerability in the packetIO daemon of Juniper Networks Junos OS Evolved on PTX10003, PTX10004, and PTX10008 allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). Continued receipt of these crafted packets will cause a sustained Denial of Service condition. This issue affects Juniper Networks Junos OS Evolved all versions prior to 20.4R2-S3-EVO on PTX10003, PTX10004, and PTX10008. This issue does not affect: Juniper Networks Junos OS Evolved versions 21.1R1-EVO and above; Juniper Networks Junos OS. | |||||
| CVE-2021-31367 | 1 Juniper | 10 Junos, Ptx1000, Ptx10001-36mr and 7 more | 2021-10-25 | 2.9 LOW | 6.5 MEDIUM |
| A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on PTX Series allows an adjacent attacker to cause a Denial of Service (DoS) by sending genuine BGP flowspec packets which cause an FPC heap memory leak. Once having run out of memory the FPC will crash and restart along with a core dump. Continued receipted of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S6; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos Evolved is not affected. | |||||
| CVE-2021-0289 | 1 Juniper | 229 Acx1000, Acx1100, Acx2000 and 226 more | 2021-07-28 | 2.9 LOW | 5.3 MEDIUM |
| When user-defined ARP Policer is configured and applied on one or more Aggregated Ethernet (AE) interface units, a Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability between the Device Control Daemon (DCD) and firewall process (dfwd) daemons of Juniper Networks Junos OS allows an attacker to bypass the user-defined ARP Policer. In this particular case the User ARP policer is replaced with default ARP policer. To review the desired ARP Policers and actual state one can run the command "show interfaces <> extensive" and review the output. See further details below. An example output is: show interfaces extensive | match policer Policer: Input: __default_arp_policer__ <<< incorrect if user ARP Policer was applied on an AE interface and the default ARP Policer is displayed Policer: Input: jtac-arp-ae5.317-inet-arp <<< correct if user ARP Policer was applied on an AE interface For all platforms, except SRX Series: This issue affects Juniper Networks Junos OS: All versions 5.6R1 and all later versions prior to 18.4 versions prior to 18.4R2-S9, 18.4R3-S9 with the exception of 15.1 versions 15.1R7-S10 and later versions; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; This issue does not affect Juniper Networks Junos OS versions prior to 5.6R1. On SRX Series this issue affects Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.4 versions prior to 19.4R3-S4; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect 18.4 versions prior to 18.4R1 on SRX Series. This issue does not affect Junos OS Evolved. | |||||
| CVE-2021-0280 | 1 Juniper | 25 Junos, Ptx1000, Ptx1000-72q and 22 more | 2021-07-28 | 5.0 MEDIUM | 7.5 HIGH |
| Due to an Improper Initialization vulnerability in Juniper Networks Junos OS on PTX platforms and QFX10K Series with Paradise (PE) chipset-based line cards, ddos-protection configuration changes made from the CLI will not take effect as expected beyond the default DDoS (Distributed Denial of Service) settings in the Packet Forwarding Engine (PFE). This may cause BFD sessions to flap when a high rate of specific packets are received. Flapping of BFD sessions in turn may impact routing protocols and network stability, leading to a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects only the following platforms with Paradise (PE) chipset-based line cards: PTX1000, PTX3000 (NextGen), PTX5000, PTX10008, PTX10016 Series and QFX10002 Series. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R3-S5 on PTX Series, QFX10K Series; 18.2 versions prior to 18.2R3-S8 on PTX Series, QFX10K Series; 18.3 versions prior to 18.3R3-S5 on PTX Series, QFX10K Series; 18.4 versions prior to 18.4R2-S8 on PTX Series, QFX10K Series; 19.1 versions prior to 19.1R3-S5 on PTX Series, QFX10K Series; 19.2 versions prior to 19.2R3-S2 on PTX Series, QFX10K Series; 19.3 versions prior to 19.3R3-S2 on PTX Series, QFX10K Series; 19.4 versions prior to 19.4R3-S2 on PTX Series, QFX10K Series; 20.1 versions prior to 20.1R3 on PTX Series, QFX10K Series; 20.2 versions prior to 20.2R2-S3, 20.2R3 on PTX Series, QFX10K Series; 20.3 versions prior to 20.3R2 on PTX Series, QFX10K Series; 20.4 versions prior to 20.4R2 on PTX Series, QFX10K Series. | |||||
| CVE-2021-0263 | 1 Juniper | 10 Junos, Ptx1000, Ptx10001-36mr and 7 more | 2021-05-04 | 4.3 MEDIUM | 5.9 MEDIUM |
| A Data Processing vulnerability in the Multi-Service process (multi-svcs) on the FPC of Juniper Networks Junos OS on the PTX Series routers may lead to the process becoming unresponsive, ultimately affecting traffic forwarding, allowing an attacker to cause a Denial of Service (DoS) condition . The Multi-Service Process running on the FPC is responsible for handling sampling-related operations when a J-Flow configuration is activated. This can occur during periods of heavy route churn, causing the Multi-Service Process to stop processing updates, without consuming any further updates from kernel. This back pressure towards the kernel affects further dynamic updates from other processes in the system, including RPD, causing a KRT-STUCK condition and traffic forwarding issues. An administrator can monitor the following command to check if there is the KRT queue is stuck: user@device > show krt state ... Number of async queue entries: 65007 <--- this value keep on increasing. The following logs/alarms will be observed when this condition exists: user@junos> show chassis alarms 2 alarms currently active Alarm time Class Description 2020-10-11 04:33:45 PDT Minor Potential slow peers are: MSP(FPC1-PIC0) MSP(FPC3-PIC0) MSP(FPC4-PIC0) Logs: Oct 11 04:33:44.672 2020 test /kernel: rts_peer_cp_recv_timeout : Bit set for msp8 as it is stuck Oct 11 04:35:56.000 2020 test-lab fpc4 user.err gldfpc-multi-svcs.elf: Error in parsing composite nexthop Oct 11 04:35:56.000 2020 test-lab fpc4 user.err gldfpc-multi-svcs.elf: composite nexthop parsing error Oct 11 04:43:05 2020 test /kernel: rt_pfe_veto: Possible slowest client is msp38. States processed - 65865741. States to be processed - 0 Oct 11 04:55:55 2020 test /kernel: rt_pfe_veto: Memory usage of M_RTNEXTHOP type = (0) Max size possible for M_RTNEXTHOP type = (8311787520) Current delayed unref = (60000), Current unique delayed unref = (10896), Max delayed unref on this platform = (40000) Current delayed weight unref = (71426) Max delayed weight unref on this platform= (400000) curproc = rpd Oct 11 04:56:00 2020 test /kernel: rt_pfe_veto: Too many delayed route/nexthop unrefs. Op 2 err 55, rtsm_id 5:-1, msg type 2 This issue only affects PTX Series devices. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS on PTX Series: 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 18.2R1. | |||||
| CVE-2021-0247 | 1 Juniper | 20 Junos, Ptx1000, Ptx10001-36mr and 17 more | 2021-04-30 | 6.8 MEDIUM | 5.5 MEDIUM |
| A Race Condition (Concurrent Execution using Shared Resource with Improper Synchronization) vulnerability in the firewall process (dfwd) of Juniper Networks Junos OS allows an attacker to bypass the firewall rule sets applied to the input loopback filter on any interfaces of a device. This issue is detectable by reviewing the PFE firewall rules, as well as the firewall counters and seeing if they are incrementing or not. For example: show firewall Filter: __default_bpdu_filter__ Filter: FILTER-INET-01 Counters: Name Bytes Packets output-match-inet 0 0 <<<<<< missing firewall packet count This issue affects: Juniper Networks Junos OS 14.1X53 versions prior to 14.1X53-D53 on QFX Series; 14.1 versions 14.1R1 and later versions prior to 15.1 versions prior to 15.1R7-S6 on QFX Series, PTX Series; 15.1X53 versions prior to 15.1X53-D593 on QFX Series; 16.1 versions prior to 16.1R7-S7 on QFX Series, PTX Series; 16.2 versions prior to 16.2R2-S11, 16.2R3 on QFX Series, PTX Series; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2 on QFX Series, PTX Series; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3 on QFX Series, PTX Series; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7 on QFX Series, PTX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3 on QFX Series, PTX Series; 18.1 versions prior to 18.1R3-S9 on QFX Series, PTX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on QFX Series, PTX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1 on QFX Series, PTX Series; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R2-S7, 18.4R3 on QFX Series, PTX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on QFX Series, PTX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on QFX Series, PTX Series. | |||||
| CVE-2021-0270 | 1 Juniper | 13 Junos, Ptx1000, Ptx10001-36mr and 10 more | 2021-04-28 | 4.3 MEDIUM | 5.9 MEDIUM |
| On PTX Series and QFX10k Series devices with the "inline-jflow" feature enabled, a use after free weakness in the Packet Forwarding Engine (PFE) microkernel architecture of Juniper Networks Junos OS may allow an attacker to cause a Denial of Service (DoS) condition whereby one or more Flexible PIC Concentrators (FPCs) may restart. As this is a race condition situation this issue become more likely to be hit when network instability occurs, such as but not limited to BGP/IGP reconvergences, and/or further likely to occur when more active "traffic flows" are occurring through the device. When this issue occurs, it will cause one or more FPCs to restart unexpectedly. During FPC restarts core files will be generated. While the core file is generated traffic will be disrupted. Sustained receipt of large traffic flows and reconvergence-like situations may sustain the Denial of Service (DoS) situation. This issue affects: Juniper Networks Junos OS: 18.1 version 18.1R2 and later versions prior to 18.1R3-S10 on PTX Series, QFX10K Series. | |||||